Cooling Stone (Cooling transfer from minus 80 degrees to plus 120 degrees),
– used in defreezer,glycol defreezer, water cooler, bulk cooler, milk cooler, Tawa ice-cream machine,cooling stone ice cream machine direct pest coil with stone to avoid solder for better cooling efficiency.
Non thermal:
– For visicular defreeze glass top frame pasting partition, leakage proof of ice box.
– Others: Leakage proof of AC coil chiller (to avoid brazing), and high temp. for air filter used in steel plant. cement factory
Other Uses:
IT ALSO USED IN ROCKWOOL PASTING WITH METAL(SS,MS)SANDWITCH PANNEL WHERE NO ADHESIVE WILLWORK.(IN ARAL DITE WHEN IT WILL BE APPLIED IT WILL FLOW WHERE OUR PASTE AS IT IS WHEN HEAT WILL GENARATE.AND ALSO POROUS ARE THERE IT WILL ABSORBE ALL ADHESIVE EXCEPT OUR PASTE THIS IS THE MAIN CHARACTERSTICS OF OUR PASTE IN INSULATION)
GLASS WOOL WILL ALSO BE STICKED .USED IN AHU INSULATION (AIR HANDLING UNIT).
USED IN AIR FILTER ALSO.AUTOMOBILE FILTER’S MOLD CAP ALSO.USED IN CABLE JOINTS , USED IN BOAT FILL UP ALSO (CRACK FILLUP).
IT’S A UNIQUE FEATURE IN PRE FILTER (AIR FILTER).
ITS ALSO CALLED POTTING PASTE YOU CAN PUT IN PRE FILTER OR MINI FLIT OR MICRO FILTER AT A TIME BOTH UPPER AND LOWER SIDE OF FILTER)
WE ARE MFGING.HIGH TEMPERATURE CHEMICAL ALSO TEMPERATURE WILL RESIST MORE THAN 400 DEGREE CELCIOUS.THIS TYPE OF FILTER USED IN MEDICINE FACTORY AND STEEL FACTORY.
2. This thermal paste will have a Cooling transfer from Minus 80 degrees to plus 120 degrees of your cupper weir.
3. Cooling Stone: Providing expert cooling solution to the defreeze, water cooler, milk cooler, bulk cooler, glass top display counter, wine table freezer.
4. Improving cooling efficiency.
5. Improving energy savings by using low compressor motor for high cooling.
6. Providing longevity to the copper coil attached to the body with a high gripping strength comparatively to solder without corrosion for better cooling efficiency.
– Specifically designed for use on all types of flues e.g. stainless steel, metal sheet, metal to copper, metal to cloth, metal to metal, vitreous enamel, ceramic flue pipes, concrete and pumice block, mould etc. It possesses good cohesion and application properties and will exchange the effects of heat from temperatures of -80to150°C.
Fixing or joining metals to copper, metal to metal, metal to cloth ,good conductor, excellent exchanger of heat, mould(cap in air filter cooling industries) making, concrete, stone, silicate fiber materials, any casting purpose, potting in anywhere, gap filliping and many other surfaces. Also use to AVOID SOLDERING because of high gripping strength as well as heat transfer
Bonding – Yes
Encapsulation – No
Thick Sections – yes
Casting, moulding, bonding with metal to metal, copper ,foil paper to metal
• Constituents are inorganic, oxide, silca ,Iso, trilaute, silca zel etc.
• Economical in cost and application
• exchange temperatures -78 to 150°C – Strong adhesive properties at room temperatures once it is cured it will never melt until temp. reaches more than 150degree
• It is used successfully with Metal to metal, metal to copper ,even also to paper, to cloth, mould making, casting, air filter potting ceramics, glass, metals, concrete, stone, silicate fibre materials and many other surfaces, either to themselves or to each other.
• Good cohesion – and will give good joint and gap-filling properties
• Product will resist the attack of organic solvents, oils, mould, fungi and acids.
• Sets to a hard and rigid ceramic mass which should not deteriorate under thermal shock, or age, under normal conditions. Hardens by air drying and operational heat which improves and strengthens seals and joints.
• RoHS compliant.
• For product supplied in plasti carbo- Stir contents of the container prior to use, to overcome the effects of any settlement of the ingredients during storage.
• Ensure that all surfaces to be bonded sealed or insulated, are degreased, clean and free from contamination.
• A light surface abrasion of the material to be bonded will increase the amount of surface area available for adhesion and will give improved mechanical key.
• Apply the adhesive to all surfaces to be bonded.
• To be bonded, ensure that all surface are fully wetted by the adhesive.
• Secure the components and allow the adhesive to set and harden.
• The ease by which full curing can be achieved is dependant on the porosity of the substrate, as well as the amount of available surface through which the adhesive film can dry.
• If quantity will be more than 500 gm curing will be fast, if less quantity surface will absorb the heat curing will be late
• CHECK THE APPLIED SURFACE ALWAYS FOR FULLY CURED
• SOMETIMES SOME MOISTURE CONTACT IF IT HAPPENS ADD MOISTURE POWDER OR CONTACT OUR REPRESENTATIVES
• IF MOISTURE CONTACTS AFTER MIXING FOAM WILL COME,CURING TIME 25 to 30 MNTS,IT CAN BE INCREASE OR DECREASE ACCORDING TO CUSTMER”S WISH.SOLDERING NOT NECESSERY CAN BE USE BY EMPTY SILICON TUBE USING GUN.
• MIXING RATIO BY VOLUME :1KG WHITE(PEST) TO _150GM BLACK(HARDNER)
• MIXING RATIO BY WIGHT :5:1 :(BEST TO USE TAKE 200GM PEST ADD 30 GMS HARDNER MIX AND PUT IN AN EMPTY SILICON CARTAGE USING GUN THEN APPLY .)
• CURING SCHEDULE @ ROOM TEMP.
• COMPREHENSIVE STRENGTH 650_1000 KG/CM VISCOSITY _ @ 25 DEGREE CENTIGRADE BY VISCO METER _32000_36000 CPS.
• LAP STRENGTH 800_100 KG/CM, TEMPERATURE TRANSFER FROM -80 DEGREE TO + 150DEGREE
• THIS HAS BEEN TESTED IN DE FREEZER COOLING TEST AS WELL AS FURNACE FOR HARDNESS AND REVEALED ABOVE PROPERTIES FOR YOUR INFORMATION.